Singer Heavy Duty 4411 Manual do Utilizador

4411 Instruction Manual

- corresponding. (1/2)- Snap thread into thread guide. (3)- Wind thread clockwise around bobbin winder tension discs. (4)- Thread bobbin as illustrate

When inserting or removing the bobbin, the needle mustbe fully raised.Attention:1. Insert the bobbin in the bobbin case with the threadrunning counter

216875This is a simple operation but it is important to carry out correctlyas by not doing so .- Start by raising the needle to its highest point (1),

123Hold the upper thread with the left hand. Turn the handwheel(1) towards you (counterclockwise) lowering, then raisingneedle.If it is difficult to r

11BACD1Upper thread tensionLower thread tensionPlease note:Basic thread tension setting: "4". (1)To increase the tension, turn the dial to t

12The diagram on this page display the stitch patterns availableon the machine.The Pattern Selector Dial may be turned in either direction.a. Reverse

13The needle position can be altered with the "Three needleposition dial". For normal work, the needle position is middle.For edge stitching

141243210.5Function of stitch width dialFunction of stitch length dial while zig-zag stitchingFunction of stitch length dial for when straight stitchi

15To begin sewing, set the machine for straight stitch. (1)Place the fabric under the presser foot with the fabric edgelined up with the desired seam

Turn the handwheel toward you (counterclockwise) to bringthe thread take up lever to its highest position, raise thepresser foot and remove work behin

When using an electrical appliance, basic safety should always befollowed, including the following:Read all instructions before using this sewing mach

1721For hems on curtains, trousers, skirts, etc.Blind hem for stretch fabrics.Blind hem for firm fabrics.Set the Stitch Width Dial ata setting appropr

18PrepareNote:Tips:1. Take off the all purpose foot and attach the buttonhole foot.Adjust the Stitch Length Dial in the " " to set stitch de

19Stitch density on right and left sides of buttonhole can beadjusted by buttonhole balance control dial.This dial should usually be in a neutral posi

204312Move the drop feed control to right side to lower the feeddogs. (1)Change the all purpose foot to the button sewing foot. (2)Set the stitch leng

1221Hold the removable extension table horizontally, and push itin the direction of the arrow. (1)To remove the extension table, pull it toward the le

1234acdefbbaeg22Raise the presser bardge/ quiltingdge/ quilting(a) with the presser foot lifter. Attachthe presser foot shank (b) as illustrated. (1)L

23Heavy woolen, overcoat fabrics, upholstery fabrics, someleathers and vinyls.EXPLANATIONStandard sharp needles. Sizes rangethin to large. 9 (70) to 1

24For ordinary sewing, keep the feed dog up, for freehandembroidery, sewing on buttons and darning, drop the feeddog.To raise (a) and lower (b) feed d

25ACBABCD12Change the needle regularly, especially if it is showing signsof wear and causing problems. For best sewing resultsalways use SINGER Brand

1226ABDisconnect the machine from the power supply by removingthe plug from the main socket!Replace bulb with same type rated 15 watts (110-120V area/

As the owner of a new Singer sewing machine, you are about to begin an exciting adventure increativity. From the moment you first use your machine, yo

Problem Cause CorrectionUpper threadbreaksLower threadbreaksSkipped stitchesNeedle breaksLoose stitchesSeams gather orpuckerUneven stitches,uneven fee

Please note that on disposal, this product must be safely recycled in accordance with relevantNational legislation relating to electrical/electronic p

List of ContentsMachine BasicsSewingGeneral InformationMaintenance and TroubleshootingPrinciple Parts of the Machine...

1. Thread tension dial2. Presser foot pressure adjustment3. Thread take-up lever4. Reverse sewing lever5. Thread cutter6. Presser foot7. Needle plate

14. Horizontal spool pin15. Bobbin winding spindle16. uxiliary spool pin17. Handwheel18. Buttonhole stitch balance adjustment slot19. Power and light

Connect the machine to a power source as illustrated. (1)This appliance is equipped with a polarized plug which must beused with the appropriate polar

5When sewing several layers or thick fabrics, the presser footcan be raised for easy positioning of thework. (A)to a higher positionAThe presser foot

1 Standard accessories2 Optional accessoriesmhgefijlkabcd006806008 006905008 006914008006909008Standard accessories (1)Optional accessories (2)a. All