Singer W1630 Manual do Utilizador

oyvcyINSTRUCTION MANUAL FORSEWING MACHINEWHIITE

'Oft 5cm of thread tom bobbin and insert itbobbin case as shown.spring- o.ui ana under ‘®os.on spring and drawZ.r^' - -

INSERTING BOBBIN CASE INTO SHUTTLE RACE1. Raise needle to its highest position, pulling thread to the front, open the latch of bobbin c

Twin needle threading

drawing up bobbin thread1. Hold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and co

CONTROL DIAL1. Pattern selector dial2- Thread tension dial3- Zig-zag width dial Stitch length dial5. Reverse button11

ADJUSTING THREAD TENSIONWeakStrongUpper thread tension may be adjusted by turning the thread tension dial.FabricCorrectUpper threadBobbin threadIncorr

regulating the presser foot pressureDROP FEEDThe. a. a few ..es wHen you wan. .o cent., the feeding of fahne hy you. You may then deter

CHANGING NEEDLE1. Raise needle to its highest position.2. Loosen neeaie clamp screw and remove old needle.3. With the flat side of the needle facin

fabric • THREAD • NEEDLE TABLEFabricThreadNeedleVHA-1LightNylon80 CottonTricot60 S, Fiber9VA.Silk50 silkWool silk50 S. Fiber Silk11Medium60-80Cotton

WHITE SEWING MACHINE COMPANYRecord In space provided below the Serial No. and Model No. of this appliance.The Serial No. Is located on Bed Plate.The M

TO START SEWINGImportant Hints.1. Raise the take-up lever to its highest position when starting and stopping sewing. ,Hold both threads about 10

TO FINISH SEAM1. Sew to the edge of seam. 2. Push the reverse button and sew in reverse for about 3—4 cms.3. Raise needle to its highest position

STRAIGHT STITCH1. This type of stitching is the one used most frequently.2. The z.g-zag presser foot can be used for both straight and zig-zag sewmg

OVERCASTING1/Use these stitches fo edges.r oversewing roughIiSTRAIGHT STRETCH STITCHUse this stitch With knitted, tricot or other stretchy fa

BLIND STITCH1. Fold fabric as shown.2. To finish seam as shown.21

Adjust width and needle position to obtain correct seam.Needle is not piercing edge of fold at all.Needle is pierces edge of fold too much.C

'4 ' /BUTTOIV SEWIIMGplate see page lyh Lower drop feed.2- Use button presser ,P'ace button between4- Manually turn h ^ and fabric an

ZIPPER SEWINGSelect straight stitch.1. Fold the fabric about 2cm and place fabric under foot.2. Zipper foot is designed to sew closeto a rais

Select stitch length dial in area indicated.BUTTON HOLE SEWINGPattern selector dialEStepsSettings1. Set dial to "1" position.2. Sew left s

HEMMING1. Raise the foot and the needle to its highest position. Replace the foot with the hemmer foot.2, Fold over the fabric edge by about

CONTENTSName of Parts... ’Accessories...Before sewing (Power supply and Sewing lamp)...

TWIN NEEDLEThread machine as for normal sewing passing both threads through the same procedure:NB. Sewing width should not exceed the

QUILTER1. Insert supporter of quilter.2. Move quilter and adjust stitch distance.SEAM GUIDE1. Use seam guide when sewing a long seam of re

MAINTENANCE {CLEANING AND OILING)Cleaning shuttle race(A) Latch knob(B) Shuttle race cover(C) Shuttle hookOpen face cover and oil points indic

J...^^- I...i':='-' « »«W'W .i‘CHECKING PERFORMANCE PROBLEMS WHAT TO DOtoOPROBLEMPROBABLE CAUSECORRECT

NAME OF PARTS (FRONT VIEW)1 Pattern selector dial2 Pressure regulator3 Take up lever4 Thread tension dial5 Presser foot6 Shuttle cover^ Extensio

(REAR VIEW)Bobbin winder spindle

ACCESSORIESBobbin VFeltZigzag foot (On machine)Button hole footZipper footButton hole cutterScrew driverNeedle #11 #14

BEFORE SEWINGMac In1. Fit the machine plug into the machine.Power supply 2. Plug the machine to the power supply.3. Sewing speed can be varied by the

REMOVING EXTENSION TABLE1. Hold the left end of table and pull out in direction of arrow.FREE-ARM SEWING1. Especially useful when sewingsle

WINDING THE BOBBIN1. Release stop motion knob.2. Thread as shown.3. When bobbin is filled, tighten stop motion knob.Bobb5cm threadwinder spindle^